발란스 XLR과 1/4 인치 폰 잭이 기본으로 되어있는 PIP-FXQ 모쥴과 DSP파워를 사용 필터, 크로서버, 딜레이, 입력 컴프레서, 출력 리미터 등을 제공하는 PIP-DSP등 여러 가지가 모쥴을 선택할 수 있습니다.
그 외에도 앰프의 상황을 알려주는 모니터 기능이 있어서 앰프가 숏트가 나는지, 저항 값이 정확한지, 앰프의 발열량, 고 음역대의 과대 출력, 앰프 내부의 이상 여부등의 정보를 미리 알려주며 동시에 자동으로 이상을 수정하는 기능등을 수행할 수 있습니다.
Load Impedance: Safe with all types of loads. Rated for 2 to 16 ohms in Stereo, 4 to 16 ohms in Bridge-Mono and 1 to 4 ohms in Parallel-Mono mode. Required AC Mains: 50/60 Hz; 100, 120, 220 and 240 VAC (10%) units are available. All draw 100 watts or less at idle. Current, voltage and frequency requirements are provided on the units back panel. PerformanceFrequency Response: 0.1 dB from 20 Hz to 20 kHz at 1 watt . Phase Response: 10 degrees from 10 Hz to 20 kHz at 1 watt . Signal-to-Noise Ratio, Total Harmonic Distortion (THD) at full bandwidth power: Less than 0.05% from 20 Hz to 1 kHz increasing linearly to 0.1% at 20 kHz. Intermodulation Distortion (IMD): (60 Hz and 7 kHz at 4:1) Less than 0.05% from 163 milliwatts to full bandwidth power. Damping Factor: Greater than 1,000 from 10 Hz to 400 Hz. Slew Rate: (Slew rates are limited to useful levels for ultrasonic/RF protection). Greater than 13 volts per microsecond. ControlsEnable: A front panel push button used to turn the amplifier on and off. Input Ground Lift: This switch on the PIP2-FXQ is used to isolate input signal grounds from chassis ground to prevent ground loops. IndicatorsEnable: This amber front panel indicator shows the on/off status of the low-voltage power supply. ODEP: Each channel has an amber front panel indicator that shows thermal-dynamic energy reserve. Normally, each ODEP indicator is lit to show available reserve energy. In the rare event that a channel has no reserve, its indicator will dim in proportion to ODEP limiting. An ODEP indicator may also turn off under other conditions. |
Input/OutputInput Connector: Two balanced 1/4-inch phone jacks on the back panel and two balanced three-pin female XLR connectors on the factory-installed PIP2-FXQ. Output SignalStereo: Unbalanced, two-channel. ProtectionMacro-Tech amplifiers are protected against shorted, open or mismatched loads; overloaded power supplies; excessive temperature, chain destruction phenomena, input overload damage and high-frequency blowups. They also protect loudspeakers from input/output DC and turn-on/turn-off transients. ConstructionSteel chassis with durable black finish, aluminum front panel with Lexan overlay, and specially designed flow-through ventilation from front to side panels.
International Units:
|
| ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
상품이 장바구니에 담겼습니다.
바로 확인하시겠습니까?
상품이 찜 리스트에 담겼습니다.
바로 확인하시겠습니까?